- Not all data is automatically replicated
- Preflight checks
- Prevent updates to the primary node
- Finish replicating and verifying all data
- Promote the secondary node
The primary use-case of Disaster Recovery is to ensure business continuity in the event of unplanned outage, but it can be used in conjunction with a planned failover to migrate your GitLab instance between regions without extended downtime.
As replication between Geo nodes is asynchronous, a planned failover requires a maintenance window in which updates to the primary node are blocked. The length of this window is determined by your replication capacity - once the secondary node is completely synchronized with the primary node, the failover can occur without data loss.
This document assumes you already have a fully configured, working Geo setup. Please read it and the Disaster Recovery failover documentation in full before proceeding. Planned failover is a major operation, and if performed incorrectly, there is a high risk of data loss. Consider rehearsing the procedure until you are comfortable with the necessary steps and have a high degree of confidence in being able to perform them accurately.
If you are using any GitLab features that Geo doesn’t support, you must make separate provisions to ensure that the secondary node has an up-to-date copy of any data associated with that feature. This may extend the required scheduled maintenance period significantly.
A common strategy for keeping this period as short as possible for data stored
in files is to use
rsync to transfer the data. An initial
rsync can be
performed ahead of the maintenance window; subsequent
rsyncs (including a
final transfer inside the maintenance window) will then transfer only the
changes between the primary node and the secondary nodes.
Repository-centric strategies for using
rsync effectively can be found in the
moving repositories documentation; these strategies can
be adapted for use with any other file-based data, such as GitLab Pages.
ERROR - Replication is not up-to-dateeven if replication is actually up-to-date. This bug was fixed in GitLab 13.8 and later.
Run this command to list out all preflight checks and automatically check if replication and verification are complete before scheduling a planned failover to ensure the process will go smoothly:
Each step is described in more detail below.
If you have a large GitLab installation or cannot tolerate downtime, consider migrating to Object Storage before scheduling a planned failover. Doing so reduces both the length of the maintenance window, and the risk of data loss as a result of a poorly executed planned failover.
In GitLab 12.4, you can optionally allow GitLab to manage replication of Object Storage for secondary nodes. For more information, see Object Storage replication.
Database settings are automatically replicated to the secondary node, but the
/etc/gitlab/gitlab.rb file must be set up manually, and differs between
nodes. If features such as Mattermost, OAuth or LDAP integration are enabled
on the primary node but not the secondary node, they will be lost during failover.
/etc/gitlab/gitlab.rb file for both nodes and ensure the secondary node
supports everything the primary node does before scheduling a planned failover.
Run the following on both primary and secondary nodes:
gitlab-rake gitlab:check gitlab-rake gitlab:geo:check
If any failures are reported on either node, they should be resolved before scheduling a planned failover.
The SSH host keys and
/etc/gitlab/gitlab-secrets.json files should be
identical on all nodes. Check this by running the following on all nodes and
comparing the output:
sudo sha256sum /etc/ssh/ssh_host* /etc/gitlab/gitlab-secrets.json
If any files differ, replace the content on the secondary node with the content from the primary node.
The maintenance window won’t end until Geo replication and verification is completely finished. To keep the window as short as possible, you should ensure these processes are close to 100% as possible during active use.
Go to the Admin Area > Geo dashboard on the secondary node to review status. Replicated objects (shown in green) should be close to 100%, and there should be no failures (shown in red). If a large proportion of objects aren’t yet replicated (shown in gray), consider giving the node more time to complete
If any objects are failing to replicate, this should be investigated before scheduling the maintenance window. Following a planned failover, anything that failed to replicate will be lost.
You can use the Geo status API to review failed objects and the reasons for failure.
A common cause of replication failures is the data being missing on the primary node - you can resolve these failures by restoring the data from backup, or removing references to the missing data.
On the primary node, navigate to Admin Area > Messages, add a broadcast message. You can check under Admin Area > Geo to estimate how long it will take to finish syncing. An example message would be:
A scheduled maintenance will take place at XX:XX UTC. We expect it to take less than 1 hour.
To ensure that all data is replicated to a secondary site, updates (write requests) need to be disabled on the primary site:
Enable maintenance mode.
Disable non-Geo periodic background jobs on the primary node by navigating to Admin Area > Monitoring > Background Jobs > Cron, pressing
Disable All, and then pressing
geo_sidekiq_cron_config_workercron job. This job will re-enable several other cron jobs that are essential for planned failover to complete successfully.
- If you are manually replicating any data not managed by Geo, trigger the final replication process now.
- On the primary node, navigate to Admin Area > Monitoring > Background Jobs > Queues
and wait for all queues except those with
geoin the name to drop to 0. These queues contain work that has been submitted by your users; failing over before it is completed will cause the work to be lost.
On the primary node, navigate to Admin Area > Geo and wait for the following conditions to be true of the secondary node you are failing over to:
- All replication meters to each 100% replicated, 0% failures.
- All verification meters reach 100% verified, 0% failures.
- Database replication lag is 0ms.
- The Geo log cursor is up to date (0 events behind).
- On the secondary node, navigate to Admin Area > Monitoring > Background Jobs > Queues
and wait for all the
geoqueues to drop to 0 queued and 0 running jobs.
- On the secondary node, use these instructions to verify the integrity of CI artifacts, LFS objects, and uploads in file storage.
At this point, your secondary node will contain an up-to-date copy of everything the primary node has, meaning nothing will be lost when you fail over.
Finally, follow the Disaster Recovery docs to promote the secondary node to a primary node. This process will cause a brief outage on the secondary node, and users may need to log in again.
Once it is completed, the maintenance window is over! Your new primary node will now begin to diverge from the old one. If problems do arise at this point, failing back to the old primary node is possible, but likely to result in the loss of any data uploaded to the new primary in the meantime.
Don’t forget to remove the broadcast message after failover is complete.