- Disabling or enabling the automatic background verification
- Repository verification
- Using checksums to compare Geo nodes
- Repository re-verification
- Reset verification for projects where verification has failed
- Reconcile differences with checksum mismatches
- Current limitations
Automatic background verification ensures that the transferred data matches a calculated checksum. If the checksum of the data on the primary node matches checksum of the data on the secondary node, the data transferred successfully. Following a planned failover, any corrupted data may be lost, depending on the extent of the corruption.
If verification fails on the primary node, this indicates Geo is replicating a corrupted object. You can restore it from backup or remove it from the primary node to resolve the issue.
If verification succeeds on the primary node but fails on the secondary node, this indicates that the object was corrupted during the replication process. Geo actively try to correct verification failures marking the repository to be resynced with a back-off period. If you want to reset the verification for these failures, so you should follow these instructions.
If verification is lagging significantly behind replication, consider giving the node more time before scheduling a planned failover.
Run the following commands in a Rails console on the primary node:
To check if automatic background verification is enabled:
To disable automatic background verification:
To enable automatic background verification:
Go to the Admin Area > Geo dashboard on the primary node and expand the Verification information tab for that node to view automatic checksumming status for repositories and wikis. Successes are shown in green, pending work in gray, and failures in red.
Go to the Admin Area > Geo dashboard on the secondary node and expand the Verification information tab for that node to view automatic verification status for repositories and wikis. As with checksumming, successes are shown in green, pending work in gray, and failures in red.
To check the health of Geo secondary nodes, we use a checksum over the list of
Git references and their values. The checksum includes
notes, and GitLab-specific references to ensure true consistency. If two nodes
have the same checksum, then they definitely hold the same references. We compute
the checksum for every node after every update to make sure that they are all
Due to bugs or transient infrastructure failures, it is possible for Git repositories to change unexpectedly without being marked for verification. Geo constantly reverifies the repositories to ensure the integrity of the data. The default and recommended re-verification interval is 7 days, though an interval as short as 1 day can be set. Shorter intervals reduce risk but increase load and vice versa.
Go to the Admin Area > Geo dashboard on the primary node, and click the Edit button for the primary node to customize the minimum re-verification interval:
The automatic background re-verification is enabled by default, but you can disable if you need. Run the following commands in a Rails console on the primary node:
To disable automatic background re-verification:
To enable automatic background re-verification:
Geo actively try to correct verification failures marking the repository to be resynced with a back-off period. If you want to reset them manually, this Rake task marks projects where verification has failed or the checksum mismatch to be resynced without the back-off period:
sudo gitlab-rake geo:verification:repository:reset
sudo gitlab-rake geo:verification:wiki:reset
If the primary and secondary nodes have a checksum verification mismatch, the cause may not be apparent. To find the cause of a checksum mismatch:
Go to the project’s repository directory on both primary and secondary nodes (the path is usually
/var/opt/gitlab/git-data/repositories). Note that if
git_data_dirsis customized, check the directory layout on your server to be sure.
Run the following command on the primary node, redirecting the output to a file:
git show-ref --head | grep -E "HEAD|(refs/(heads|tags|keep-around|merge-requests|environments|notes)/)" > primary-node-refs
Run the following command on the secondary node, redirecting the output to a file:
git show-ref --head | grep -E "HEAD|(refs/(heads|tags|keep-around|merge-requests|environments|notes)/)" > secondary-node-refs
Copy the files from the previous steps on the same system, and do a diff between the contents:
diff primary-node-refs secondary-node-refs
Automatic background verification doesn’t cover attachments, LFS objects, job artifacts, and user uploads in file storage. You can keep track of the progress to include them in Geo: Verify all replicated data.
For now, you can verify their integrity manually by following these instructions on both nodes, and comparing the output between them.
In GitLab EE 12.1, Geo calculates checksums for attachments, LFS objects, and archived traces on secondary nodes after the transfer, compares it with the stored checksums, and rejects transfers if mismatched. Please note that Geo currently does not support an automatic way to verify these data if they have been synced before GitLab EE 12.1.
Data in object storage is not verified, as the object store is responsible for ensuring the integrity of the data.